Can’t boot after installation

[fvdw]

do you get the same error when installing the disk in the lefthand slot ?

[fvdw]

and additional question, in which position is the the switch on the back side regarding raid, should be on "big" if I remember well

[Redleh]

Removed and inserted the disk again on the right side.

Code: Select all

root@(none):/ # dmesg
Linux version 2.6.39.4 (root@fvdwsl-5big2.local) (gcc version 4.8.1 (GCC) ) #47 PREEMPT Tue Feb 21 22:42:25 CET 2017
CPU: Feroceon [41069260] revision 0 (ARMv5TEJ), cr=a0053177
CPU: VIVT data cache, VIVT instruction cache
Machine: LaCie 2Big Network
Clearing invalid memory bank 0KB@0x00000000
Clearing invalid memory bank 0KB@0x00000000
Clearing invalid memory bank 0KB@0x00000000
Ignoring unrecognised tag 0x00000000
Ignoring unrecognised tag 0x00000000
Ignoring unrecognised tag 0x00000000
Ignoring unrecognised tag 0x41000403
Memory policy: ECC disabled, Data cache writeback
On node 0 totalpages: 16384
free_area_init_node: node 0, pgdat c03ee948, node_mem_map c0400000
  Normal zone: 128 pages used for memmap
  Normal zone: 0 pages reserved
  Normal zone: 16256 pages, LIFO batch:3
pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
pcpu-alloc: [0] 0
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256
Kernel command line: console=ttyS0,115200 netconsole=6666@192.168.2.252/,6666@192.168.2.20/
PID hash table entries: 256 (order: -2, 1024 bytes)
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 64MB = 64MB total
Memory: 60840k/60840k available, 4696k reserved, 0K highmem
Virtual kernel memory layout:
    vector  : 0xffff0000 - 0xffff1000   (   4 kB)
    fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
    DMA     : 0xffc00000 - 0xffe00000   (   2 MB)
    vmalloc : 0xc4800000 - 0xfd800000   ( 912 MB)
    lowmem  : 0xc0000000 - 0xc4000000   (  64 MB)
    modules : 0xbf000000 - 0xc0000000   (  16 MB)
      .init : 0xc0008000 - 0xc00e7000   ( 892 kB)
      .text : 0xc00e7000 - 0xc03db000   (3024 kB)
      .data : 0xc03dc000 - 0xc03ef020   (  77 kB)
SLUB: Genslabs=13, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
Preemptable hierarchical RCU implementation.
        RCU-based detection of stalled CPUs is disabled.
        Verbose stalled-CPUs detection is disabled.
NR_IRQS:64
sched_clock: 32 bits at 166MHz, resolution 5ns, wraps every 25769ms
Calibrating delay loop... 265.42 BogoMIPS (lpj=1327104)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
NET: Registered protocol family 16
Orion ID: MV88F5182-A2. TCLK=166666667.
net2big: power up SATA hard disks
net2big: Flash writing is not yet supported.
bio: create slab <bio-0> at 0
SCSI subsystem initialized
libata version 3.00 loaded.
Switching to clocksource orion_clocksource
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 2048 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP reno registered
UDP hash table entries: 256 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
NET: Registered protocol family 1
PCI: CLS 0 bytes, default 32
Switched to NOHz mode on CPU #0
NetWinder Floating Point Emulator V0.97 (double precision)
msgmni has been set to 118
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 3) is a 16550A
console [ttyS0] enabled
loop: module loaded
Uniform Multi-Platform E-IDE driver
ide-gd driver 1.18
sata_mv sata_mv.0: version 1.28
sata_mv sata_mv.0: slots 32 ports 2
scsi0 : sata_mv
scsi1 : sata_mv
ata1: SATA max UDMA/133 irq 29
ata2: SATA max UDMA/133 irq 29
mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4
mv643xx_eth smi: probed
mv643xx_eth_port mv643xx_eth_port.0: eth0: port 0 with MAC address 00:d0:4b:83:91:95
netconsole: local port 6666
netconsole: local IP 192.168.2.252
netconsole: interface 'eth0'
netconsole: remote port 6666
netconsole: remote IP 192.168.2.20
netconsole: remote ethernet address ff:ff:ff:ff:ff:ff
netconsole: device eth0 not up yet, forcing it
ata1: SATA link down (SStatus 0 SControl 300)
ata2: SATA link down (SStatus 0 SControl 300)
mv643xx_eth_port mv643xx_eth_port.0: eth0: link up, 1000 Mb/s, full duplex, flow control disabled
console [netcon0] enabled
netconsole: network logging started
aoe: AoE v47 initialised.
i2c /dev entries driver
at24 0-0050: 1024 byte 24c08 EEPROM, writable, 1 bytes/write
mv_xor_shared mv_xor_shared.0: Marvell shared XOR driver
mv_xor mv_xor.0: Marvell XOR: ( xor cpy )
mv_xor mv_xor.1: Marvell XOR: ( xor fill cpy )
TCP cubic registered
NET: Registered protocol family 17
VFP support v0.3: not present
Freeing init memory: 892K
ata1: exception Emask 0x10 SAct 0x0 SErr 0x4010000 action 0xe frozen
SysRq : HELP : loglevel(0-9) reBoot Crash terminate-all-tasks(E) memory-full-oom-kill(F) kill-all-tasks(I) thaw-filesystems(J) show-memory-usage(M) nice-all-RT-tasks(N) show-registers(P) show-all-timers(Q) Sync show-task-states(T) Unmount show-blocked-tasks(W)
SysRq : HELP : loglevel(0-9) reBoot Crash terminate-all-tasks(E) memory-full-oom-kill(F) kill-all-tasks(I) thaw-filesystems(J) show-memory-usage(M) nice-all-RT-tasks(N) show-registers(P) show-all-timers(Q) Sync show-task-states(T) Unmount show-blocked-tasks(W)
SysRq : HELP : loglevel(0-9) reBoot Crash terminate-all-tasks(E) memory-full-oom-kill(F) kill-all-tasks(I) thaw-filesystems(J) show-memory-usage(M) nice-all-RT-tasks(N) show-registers(P) show-all-timers(Q) Sync show-task-states(T) Unmount show-blocked-tasks(W)
ttyS0: 1 input overrun(s)
SysRq : HELP : loglevel(0-9) reBoot Crash terminate-all-tasks(E) memory-full-oom-kill(F) kill-all-tasks(I) thaw-filesystems(J) show-memory-usage(M) nice-all-RT-tasks(N) show-registers(P) show-all-timers(Q) Sync show-task-states(T) Unmount show-blocked-tasks(W)
SysRq : HELP : loglevel(0-9) reBoot Crash terminate-all-tasks(E) memory-full-oom-kill(F) kill-all-tasks(I) thaw-filesystems(J) show-memory-usage(M) nice-all-RT-tasks(N) show-registers(P) show-all-timers(Q) Sync show-task-states(T) Unmount show-blocked-tasks(W)
ata1: edma_err_cause=00000010 pp_flags=00000000, dev connect
SysRq : HELP : loglevel(0-9) reBoot Crash terminate-all-tasks(E) memory-full-oom-kill(F) kill-all-tasks(I) thaw-filesystems(J) show-memory-usage(M) nice-all-RT-tasks(N) show-registers(P) show-all-timers(Q) Sync show-task-states(T) Unmount show-blocked-tasks(W)
SysRq : HELP : loglevel(0-9) reBoot Crash terminate-all-tasks(E) memory-full-oom-kill(F) kill-all-tasks(I) thaw-filesystems(J) show-memory-usage(M) nice-all-RT-tasks(N) show-registers(P) show-all-timers(Q) Sync show-task-states(T) Unmount show-blocked-tasks(W)
ata1: SError: { PHYRdyChg DevExch }
SysRq : Changing Loglevel
Loglevel set to 5
ata1: hard resetting link
ata1: link is slow to respond, please be patient (ready=0)
ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata1.00: ATA-8: WDC WD1002FAEX-00Y9A0, 05.01D05, max UDMA/133
ata1.00: 1953525168 sectors, multi 0: LBA48 NCQ (depth 31/32)
ata1.00: configured for UDMA/133
ata1: EH complete
scsi 0:0:0:0: Direct-Access     ATA      WDC WD1002FAEX-0 05.0 PQ: 0 ANSI: 5
fvdw1 disk index before get_sd_name = 0
device-name= sata_mv
fvdw2 disk index after get_sd_name = 1
fvdw3 prefix[0]=s prefix[1]=d
fvdw4 disk diskname= sdb
sd 0:0:0:0: [sdb] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB)
sd 0:0:0:0: [sdb] Write Protect is off
sd 0:0:0:0: [sdb] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
 sdb: sdb1 sdb2 sdb3 sdb4 < sdb5 sdb6 sdb7 sdb8 >
sd 0:0:0:0: [sdb] Attached SCSI disk
root@(none):/ #

[fvdw]

now it is recognized as sdb, so for installing the firmware you should move it to the lefthand slot so it is recognized as sda

ps please give the info on the posdition of the swictch

[fvdw]

why do you get output like this

SysRq : HELP : loglevel(0-9) reBoot Crash terminate-all-tasks(E) memory-full-oom-kill(F) kill-all-tasks(I) thaw-filesystems(J) show-memory-usage(M) nice-all-RT-tasks(N) show-registers(P) show-all-timers(Q) Sync show-task-states(T) Unmount show-blocked-tasks(W)

[Redleh]

why do you get output like this

SysRq : HELP : loglevel(0-9) reBoot Crash terminate-all-tasks(E) memory-full-oom-kill(F) kill-all-tasks(I) thaw-filesystems(J) show-memory-usage(M) nice-all-RT-tasks(N) show-registers(P) show-all-timers(Q) Sync show-task-states(T) Unmount show-blocked-tasks(W)

I do not know!! :dontknow

[fvdw]

why do you get output like this

SysRq : HELP : loglevel(0-9) reBoot Crash terminate-all-tasks(E) memory-full-oom-kill(F) kill-all-tasks(I) thaw-filesystems(J) show-memory-usage(M) nice-all-RT-tasks(N) show-registers(P) show-all-timers(Q) Sync show-task-states(T) Unmount show-blocked-tasks(W)

I do not know!! :dontknow

This doesn't come from fvdw-sl kernel, must be something else, probably you arer sending a SysRq (break) via the telnet client.

The SysRq facility is a method of interacting with the kernel directly, and is normally used when the switch/device is hung or not working correctly. There are several triggers to reach SysRq and it is possible that one of them may have been invoked inadvertently. These triggers include:

Pressing the SysRq key while connected to the console
Pressing the Break key while connected to the console
Issuing a Send Break from a telnet session into the switch
Issuing echo ? > /proc/sysrq-trigger

[fvdw]

and additional question, in which position is the the switch on the back side regarding raid, should be on "big" if I remember well

please answer this

[Redleh]

It was on big, but i swaped to safe.
I will turn it back to BIG

[Redleh]

Hi!

I´m having a issue with booting the NAS.
I managed to install the firmware, as I did before, and have manage the nas do boot normaly anda have web access.
But when it reboots, it only reboots normaly some times.
The other times, the rear right and the front light blinks blue and red, for 5sec. Than both rear light came solid blue, and after 3sec. the front light starts blinking red for 2sec. and the system shutdown.
:elec)
Can my boot load be corrupted??

Thanks for the help!